Wednesday, January 5, 2011

Samsung I780 hard reset

1. Power off the phone
2. Hold down the begin call and end call buttons (green & red)
3. Press and hold the power button
4. Once the phone’s status LED turns red, “RELEASE” the power button but KEEP the other 2 pushed. Very important to do this !!!!!
5. You will get a prompt to press the space key to format, or any other key to continue

How to Do Hard Reset Samsung I8000

To Perform Hard Reset For New Samsung GT-I8000 Do this:

Call + Power + Volume + Keylock + Reset


Good Flashing For All

GUIDE: How to flash M8800 Pixon



GUIDE: How to flash M8800 Pixon






First thing to always remember, is BACK UP YOUR PHONE, Pictures,wallpapers,music, and any contacts you have saved on your phone. I am not responsible for any damage to you, your phone, computer, or lost of data in this process. This is a guideline intended for professional technicians.
USE AT YOUR OWN RISK!!!
1. USB cable that came with your phone.
2. Samsung PC Studio 3 witch can be found here:
http://www.samsung.com/uk/support/d..._ia_cd=01011800
Install this software first, it contains the drivers for your phone, and has every thing you need for backup.
3. Multiloader v5,50 http://www.4shared.com/file/75565159...ader_V550.html
5. Newest unbrranded firmware MEGAUPLOAD - The leading online storage and file delivery service

-----------------------------Now you are ready to begin-----------------------------------
1. Make sure Samsung PC Studio is installed and communicates with your phone. And unpack the firmware in a folder you can easily find it.
2. Remove the Sim and MicroSD from your phone and replace the battery.
3. With the phone OFF connect the phone and computer with the USB cable.
4. While holding the no. 9 button on the phones key pad, tap the power button, the phone screen will come on black with a red stripe that says "Download" ( For Tocco and Pixon users : Hold down the "Volume -" button on the left side, and the "Camera" button on the right, then press the "Power" button = all three buttons need to be pressed together. Your phone should start up into a red\blue on black bootloader screen.)

5. Now run MultiLoader v5.33
6. Select the radio button that includes MSM6275/MSM6280.

7. Select Boot Change and Full Download.
8. Then click Boot, and select the boot files from the unpacked firmware folder.

9. Click the Amss, Rsrc1, and Rsrc2.
10. Then press the Factory FS tab, and select the appropriate files from the firmware folder also.
11. Select (Low).r2c NOT (Mid).r2c. (Phone may not restart if you select mid)
12. FOTA and ETC fields are left blank.

13. Click the Port Search button, it will find your phone and show the com port is ready.
14.Click the download button and be patient, this will take a few minutes to complete.

15.When it's finished, it will show "ok complete".

16.Unplug the phone from the USB cable, reinstall the sim, MicroSD, and power up the the phone.
17. Now with every thing complete, perform a hard reset by typing *2767*3855# into the hand set.
18. When the phone resets type *#1234# into your handset to check your new firmware ver.



###IF ANY FILE NOT FOUND SEARCH IN GOOGLE-I HOPE YOU GOT IT###

How to Unlock new QUALCOM (3G ) Samsung models

This is short manual for new 3G Samsung phones (U900, U800, F480, U700 etc)


In order to unlock it, do the following steps:

Power on the phone and activate "QUALCOM" USB Mode - type *#782872# and confirm.
Connect phone to PC USB port with USB cable
Make sure to install QUALCOM drivers ! ! ! (Support/Drivers/Samsung/Qualcom_driver.rar)
Start Samsung Rocker and select Your model
Com port selection is done automaticaly, You DO NOT NEED to select port
Check "Unlock" and click "Do Job"
Thats it
If everything is done well, You should have following log in Samsung Rocker :

Samsung Rocker v1.21Beta

Loaded 456 models

Available COM ports: COM1, COM3, COM17, COM29

Doing Job, Please Wait
Using \\.\COM30 port

Modell: SGH-U900
MSLAddress: R6VQ488053
IMEI: 352442-02-184326-1
Calculating... OK
MSL2 Code: PASSED
MSL2 Password: PASSED
Closed \\.\COM30 port
Using \\.\COM15 port
Unlocking... OK
Unlock & Unfreeze: DONE
Closed \\.\COM15 port
Using \\.\COM30 port
Resetting Phone

Closed \\.\COM30 port


To exit QUALCOM mode, type *#726872# via keyboard.

1202 not charging 100%

RX and TX Service Network Problems

RX and TX Service Network Problems

there is two
sections in network 1, Rx section. 2, Tx section. all technicians need
to use manual searching in mobile phone, testing for Rx section and Tx
section.

HOW TO FIND WHICH SECTION IS FAULT Tx (or) Rx?

Testing Rx section

use manual
for Testing Rx section, after searching Rx section good condition means
it shows network list like Airtel, hutch, (or) any other network list
in your area,

If Rx section bad condition after searching it shows NO NETWORK FOUND

1, after searching it shows network list means Rx section is ok.
2, after searching it shows NO NETWORK FOUND or some networks missing means Rx section is faulty.

Testing Tx section

Use manual
for testing Tx section, after searching it shows network list, then you
can choose your simcard network, if Tx section is good condition it
shows HOME NETWORK SELECTED, if Tx section is fault it shows NO ACCESS.


1, after selecting network it shows HOME NETWORK SELECTED means Tx section is ok.
2, after selected network it shows NO ACCESS means Tx section is fault.


Information of Rx section components and ics nokia dct-3 tech

1, antenna switch

2, RF IC ( Hagar ic )

3, AUDIO IC ( cobba ic)

4, crystal oscillator

5, filters

6, VCO (voltage control oscillator



Information of Tx section components and ics nokia dct-3 tech

1, PF IC (PA IC)


Information of Rx section components and ics nokia dct-4 tech

1, antenna switch

2, filters

3, RF IC

4, crystal oscillator

5, VCO (voltage control oscillator)

6, UEM IC


Information of Tx section components and ics nokia dct-4 tech


1, PF IC (PA IC)


HOW TO SERVICE Rx SECTION FAULT ?

Solution for Rx section no network found fault nokia dct-3 technolagy

1,clean the pcb well and Rehot (if not ok follow one by one solutions)

1, give antenna switch jumper

2, Rehot the RF IC

3, Rehot the AUDIO IC

4, Reball the RF IC

5, change the RF IC

6, change the AUDIO IC

7, change the crystal oscillator


Solution for Rx section NO NETWORK FOUND fault nokia dct-4 technology

1, clean the pcb well and Rehot (if not ok follow one by one solutions)

2, give antenna switch jumper

3, Reheat the RF IC

4, change the crystal oscillator

5, Reball the RF IC

6, change the RF IC

7, Change filters


HOW TO SERVICE Tx SECTION FAULT ?


Solution for Tx section NO ACCESS fault nokia dct-3 technolagy

1, Change the PF IC


Solution for Tx section NO ACCESS fault nokia dct-4 technolagy


1, Change the PF IC


SOLUTION FOR OTHER NETWORK FUALT


Solution for low network coverage, all models


1, give jumper from antenna contact to cabinet antenna

2, change the antenna switch


Solution for dct-3 technology
When switch on the mobile it shows full network after few seconds its goas down


1, flash - Rebuild ime - UI settings (if not ok follow 2nd solution)

2, check the track from battery +ve point to PA IC, if track is ok then change the good PF IC.



Solution for dct-4 technology
When switch on the mobile it shows full network after few seconds its goas down


1, write good pm file (if not ok follow 2nd solution)

2, change the PF IC, if still the problem same check the PF power track to battery +ve point

Nokia 6300 3110c 3500c short solution.

Successfully convert nokia 2760h rm-391 to rm-258

Successfully convert nokia 2760h rm-391 to rm-258

1.erasse the whole flasher
2.full flash with rm-258 update file
3.write full pm of nokia 2760 rm-258
4.do unlock
5.ui settings.
6.chang filter with 2626 or make jumper

100% tested by me.

1110,1112.1600.2310,6030 Booting jumper

Basics of mobile phone

2700c DATA_MISMATCH: RX2 Pin not Connected

1ST BOOT : C0,07 [Rm-561] [2.1.0.0]
RAPx ID : 000000010000022600010006030C192101033000
EM 1 ID : 00000296
EM 2 ID : 00000B22
RAPx PBID : 19800006C01B8E565DF765F0E25CAAE674E2C5F8
RAPx MODE : 00
RAPx HASH : 9DDBFCFE6E73CED7D8C6268C8EB85723
RAPx ROID : 273F6D55DFAAF68F
CMT 1ST Boot OK
CMT 2ND Bt: RAP3Gv3_2nd.fg, Ver: 9.11.1
CMT FLID0 : 00898982-00008A31, Int NU48F512
CMT FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
CMT MCID0 : FFFF0000-00000000
CMT 2ND Boot OK
CMT ALGO : RAP3Gv3_algo.fg, Ver: 9.17.0
CMT VPP : Internal
DUAL LINE : True
CMT ALG Boot OK
IMAGE : rm561__09.80.mcusw
ERASE Skipped
DATA_MISMATCH: RX2 Pin not Connected, or Used 5 Pin Cable !
DATA_BLK_ERROR at: 0x00000400, 03
ERR: CMT FLASH WRITE D_BLK C7012D0103CD000090000000F172, LN: 0x0000A0, Time: 05:52
Process Failed, Repowering Mobile




Try

Use 7 pin cable or universal cable or usb flash


If not solve

Then try this


Then Try Flash With Update File

Nokia all Pinout

Error information on ufs and jaf

Who knew there was a need or do not know yet

Description of error in UFS for nokia

1. Error HDAT 14.
a. Check the data cable
b. Change MJOLNER 85% weak.
2. C BUS 9 boot error.
a. Skip BT flashing
b. Change IC flash.
3. ALG 2nd boot error.
a. Check your FIA
b. CHANGE UPP
4. Platform 3, the data error DCT4
a. Change UPP
5. Error 6
a. 90% RAM
b. 10% UPP
6. ALG 1 boot error
a. Reball flash IC 3
b. CHANGE UPP
7. Error 10
a. CHANGE UPP
b. Ic flash Reball
8. Error 6 platform 7
a. Change UPP
9. Error 2 DCT4
a. UPP
10. error HDAT 14 DCT4
a. mjolner
11. WD2 boot error
a. Make sure MAINT board OK
b. Make sure mjolner OK
c. Check use PS, if it rises 0.25 A (make sure UEM OK), UPP damaged.
d. If not up / over 0.25 A, UEM damaged.


DESCRIPTION ERROR ufs.
1. Not connected 45: replace U1
2. Not connected 00: replace the C3 / U2
3. HWK dead / no connect: replace Q1 and Q2
Error Description JAF
________________________________________
Server error 1

Each will start jaf always checks to see if there is software or firmware, but the box can still be used, this message will come on until we update online

* The solution: update online

6630 error sync the phone

Check cable nothing wrong

* Try to Replace Cable TV

Unknown cmd in flash file

Flash files will be used corupted,

* Inlstall repeated flash files and flash back

The same thing for JAF error reading the article can be listened to below:

mcuid aaaa: The phone is not going on or the TX signal line data is too high after power turned on (damage to the CPU, TX less data line connected)

mcuid cccc - The phone can not be issued a signal on TX data line after UEM reset IC (BSI line is not connected properly, check the 3.3 K resistor contained in BSI line, or damaged UEM)

mcuid DDDD - phone signals can not be issued a TX line low after UEM reset the data (perhaps UEM damaged or that have long JAF customer ID 85xxxxxx capacitor with a value of 33 pico b / w mbus-ground must be removed)

mcuid EEEE - CPU there is no response to reflash the data

Error loading boot - problem could not be verified defective RAM or CPU is defective.

Error loading loader - Problems can not be verified RAM, CPU, or Flash IC is damaged.

Error loading aditional loader - Bluetooth module damaged (especially in Ic). To skip bluetooth solution while reflash the phone.

Error erase - Flash IC damaged or bad connect.

Error cmd20 - Bluetooth Ic damaged or bad connect

Error cmd14 - flash chips or old jaf problem until customer id PCB 85xxxxxx must put a 33 pico capacitor b / w mbus-gnd
Flash ic damaged or bad, or connect with old JAF customer ID 85xxxxxx capacitor with a value of 33 pico b / w mbus-ground should be removed.

If the phone can not always go to local mode, please checked contained 68K resistor in BSI line and Ground (Data cable)

N70 APE 2ND Boot ERR:

Qus:

1ST BOOT : C0,0C [Rm-84] [2.0.8.4]
OMAP ID : 17100701
OMAP MODE : 00
OMAP PBID : F4C20C12E59AFDB66E903CD81AFFFDE2E90833A7
OMAP HASH : 2C05369F57CC3C4CF9E783E83D9B512B
OMAP ROID : AB5E4ADB27A06946
RAPx ID : 000000010000022600010006000C192101002200
EM 1 ID : 00000232
EM 2 ID : 00000353
RAPx PBID : 0A60010971755D51DF6D8F422AC1AC584392887D
RAPx MODE : 00
RAPx HASH : E9EFF4BFAA5393217CA6B17755FC3E14
RAPx ROID : F28A211FCEA7B19D
CMT 1ST Boot OK
CMT 2ND Bt: RAP3Gv2_2nd.fg, Ver: 1.21.0
CMT FLID0 : 00EC2250-00000121, Sam K8S6415ETB
CMT FLCNT : 00000000000000000000000000000000000000
CMT MCID0 : FFFF0000-00000000
CMT 2ND Boot OK
CMT ALGO : RAP3Gv3_algo.fg, Ver: 9.11.0
CMT KSIG0 : 0F72BF9DE5D6711B3B1133EBCAB5914FA419C78D
CMT VPP : Internal
DUAL LINE : True
CMT ALG Boot OK
IMAGE : RM84_50705301.C0
CMT NOR Erase Area: 0x00000000-0052B469
CMT NOR Erase Area: 0x006A0000-006BFFFF
CMT NOR Erase Area: 0x006DF000-006EFFFF
CMT NOR Erase Area: 0x00700000-007EFFFF
CMT FLASH ERASE OK, Time: 00:40
Written: 7 Certificate(s)
CMT FLASH WRITE OK, Time: 00:27
1ST BOOT : C0,0C [Rm-84] [2.0.8.4]
OMAP ID : 17100701
OMAP MODE : 00
OMAP PBID : F4C20C12E59AFDB66E903CD81AFFFDE2E90833A7
OMAP HASH : 2C05369F57CC3C4CF9E783E83D9B512B
OMAP ROID : AB5E4ADB27A06946
RAPx ID : 000000010000022600010006000C192101002200
EM 1 ID : 00000232
EM 2 ID : 00000353
RAPx PBID : 0A60010971755D51DF6D8F422AC1AC584392887D
RAPx MODE : 00
RAPx HASH : E9EFF4BFAA5393217CA6B17755FC3E14
RAPx ROID : F28A211FCEA7B19D
CMT 1ST Boot OK
CMT 2ND Bt: RAP3Gv2_2nd.fg, Ver: 1.21.0
CMT FLID0 : 00EC2250-00000121, Sam K8S6415ETB
CMT FLCNT : 00000000000000000000000000000000000000
CMT MCID0 : FFFF0000-00000000
CMT 2ND Boot OK
CMT ALGO : RAP3Gv3_algo.fg, Ver: 9.11.0
CMT KSIG0 : 0F72BF9DE5D6711B3B1133EBCAB5914FA419C78D
CMT VPP : Internal
DUAL LINE : True
CMT ALG Boot OK
APE 2ND Bt: helen3_2nd.fg, Ver: 1.35.0
00000090: 00 00 ..
ERR: APE 2ND Boot FLB1_MSG_C2: 00000400000000B172 APE 2ND CONF:
IMAGE : RM84_50705301.C0
Process Failed, Repowering Mobile


what is problam
plss halp very quick



Ans:

1.Change flash cable
2.Try with Another box
3.If problem not solve by check or change flash cable that mean flash ic problems